If you use an MFT-style workbench and a track saw, keeping the guide rail perfectly aligned can be one of the biggest challenges when making repeated cuts. The HONGDUI Hooked On Wood Folding Guide Rail Clamp solves this problem by securely attaching the guide rail to your workbench while allowing it to fold up and out of the way between cuts.
Table of Contents
Built for Precision and Broad Compatibility
This folding guide rail clamp, came from Dennis over at the Hooked On Wood channel teaming up with HONGDUI, is made to improve machining precision and ease of use.
It is compatible with a wide range of leading track saw brands, including Festool, Makita, Milwaukee and Evolution G2. Whether your workshop uses tools from a single brand or a mix of brands, this clamp will meet your needs. The clamp also works with bench dogs measuring 18 mm to 22 mm in diameter. For the best performance, we recommend pairing it with HONGDUI HD30 Bench Dogs for stable, fence-proximity mounting.
Installation That Takes Seconds
There are no additional tools to install. You slide the clamp into the guide rail, position it around the bench dog, and tighten the brass thumb screws to lock everything in place. Once installed, the clamp can remain on the rail during storage. If you move to a different hole pattern on your MFT workbench, only minor repositioning is needed before you’re ready to work again.
A Faster Workflow with the Folding Hinge
The hinged design is the standout feature of this clamp. Instead of removing and repositioning the guide rail after every cut, you simply lift the rail, place the workpiece, and fold the rail back into its original position.
This matters more than it sounds, especially when you’re working in a tight workshop or handling heavy materials. Imagine loading a 6 cm thick slab or an awkward workpiece. Without these clamps, that’s a wrestling match every single time. With this clamp, you lift the rail, slide your material against a stop, fold the rail back into its exact original position, and cut.
For projects requiring multiple identical pieces, this fluid movement saves hours of frustration and labor.
Simple Height Adjustment for Accurate Cuts
Achieving perfect 90-degree cuts depends on positioning the clamps at exactly the right height relative to your workbench. If the clamps are set too low, the front of the guide rail lifts slightly. If they’re too high, the back of the rail tilts upward, which can even pull the bench dogs out of the workbench.
The clamp uses a silver thumb screw as a height stop to lock in the correct position. If you’re working with different material thicknesses, recalibration is simple: loosen the brass thumb screws, slide a scrap piece of your new material underneath, and tighten. For quick jobs, simply resting the guide rail on top of the workpiece before tightening the clamps also gives a solid setup.
Performance and Practical Limitations
The clamp works best for cutting wood between 0 mm and 40 mm thick. On some track saws, particularly Festool models, deeper cuts may cause the motor housing to contact the clamps before reaching full cutting depth.
You’ll also sacrifice a small amount of cutting width. Because the workpiece must fit between the two supporting bench dogs, most setups lose approximately 8 cm of cutting capacity compared to using the guide rail without the clamps. While this is rarely an issue for everyday work, oversized panels may require removing the clamps or repositioning the bench dogs.
Workshop Layout Matters
The hinge mechanism works best when your workbench has adequate clearance above it. If wall-mounted cabinets hang directly over your bench, you may not have room to swing the rail fully upright. The system still functions if you only lift the rail enough to slide material underneath, but the full benefits emerge when the rail can swing through its complete range without obstruction.
Price and Availability
This Folding Guide Rail Clamp is available on Banggood for $57.99 to $59.99, depending on which warehouse ships from.
The clamp is an excellent upgrade for woodworkers who regularly use an MFT workbench and track saw. While there are some trade-offs in cutting depth and width, the gains in precision, repeatability, and workflow efficiency make it a tool well worth considering for any woodworking enthusiast.
Shop the HONGDUI Hooked On Wood 2pcs Folding Guide Rail Clamp on Banggood
More woodworking tips: Build a Perfect DIY MFT Workbench Without a CNC
